Managing thermal stress when welding high-carbon steels

Welding high-carbon steel is not simply a matter of lowering heat input. Carbon and alloy content can create a hard, crack-sensitive heat-affected zone, while restraint turns normal thermal expansion into residual stress. A sound joint depends on controlling the temperature history, hydrogen level and fit-up from preparation through final cooling.

Australian fabricators encounter the problem in quenched-and-tempered shafts, moulds, wear plates and mining equipment. Newcastle workshops may receive locally produced or imported plate, while Pilbara maintenance teams often repair components far from a fabrication plant. Repeatable procedures and clear weld maps are therefore essential.

The aim is not to remove residual stress, which is impossible after fusion welding. It is to keep the heat-affected zone ductile, limit crack-driving forces and slow cooling where needed. A qualified procedure, competent operators and suitable inspection must work together; no preheat setting can compensate for poor preparation.

Why heat and restraint create failure

High-carbon grades such as EN19 and EN24 contain enough carbon for rapid hardening when welded. Similar problems occur in some quenched-and-tempered alloy steels, even where the carbon level is below the usual high-carbon threshold. Their carbon equivalent and hardenability affect how readily the weld and adjacent metal transform to martensite. Carbon-equivalent formulae help screen risk, but they do not replace testing; chemistry, thickness, restraint and cooling conditions still require engineering judgement.

Heating expands the plate, but a rigid frame, closed box section or poorly aligned joint prevents free movement. The resulting compressive stress can buckle a thin component, while contraction and transformation strains may leave the weld and heat-affected zone in tension. Local tensile stress is the main concern when a small crack can propagate through a hard zone.

Hydrogen adds another mechanism. Moisture, rust, oil, damp electrodes or contaminated grinding wheels can introduce diffusible hydrogen, which collects at susceptible locations and promotes cold cracking after the joint has cooled. Cracking may appear hours later, so an apparently sound weld immediately after cooling is not sufficient evidence of acceptability.

Build the welding procedure around the grade

Procedure design must balance two opposing risks. Low heat input can produce fast cooling, high hardness and a coarse or crack-sensitive zone; excessive input raises the chance of coarse grains, oxidation, undercut, distortion and a large softened region. The approved heat-input range must therefore be established from the grade, thickness, joint design and restraint rather than copied from a generic table. Actual heat input should be calculated from measured voltage and current, travel speed and an appropriate efficiency factor. Machine settings alone can be misleading because operator technique, lead angle and surface condition affect the result.

Preheat can lower the cooling rate and help hydrogen escape, but it must be controlled. Too little may leave a hard, crack-prone zone; too much can enlarge the heat-affected zone and reduce properties in a quenched-and-tempered steel. Measure preheat near the root at approved locations, maintain the specified interpass temperature and account for heat loss from large or cold components.

Consumables, joint preparation and welding sequence are equally important. Use approved low-hydrogen consumables, keep them dry and reject contaminated or damaged material. Clean the bevel, control root opening and avoid excessive tacking. Symmetrical sequencing, back-stepping and planned crater treatment reduce local heat accumulation and distortion. Any post-weld heat treatment requires engineering approval because it may change hardness or strength. Equipment comparisons should examine thermal control rather than speed alone; this industrial process overview offers a useful wider reference.

Match the method to Australian jobsites

In Newcastle, NSW, the steel supply chain and heavy fabrication sector make grade traceability a commercial issue as well as a technical one. A job may combine locally rolled plate with imported quenched-and-tempered bar. A fitter and welder should confirm heat numbers and procedure coverage rather than assume that all steel behaves alike. Regional supply chains add another wrinkle: workshops may be asked to match an imported grade with locally available stock without changing the engineering intent.

Pilbara crews work in extreme heat, dust and long supply chains. Field repairs may involve a component too large to heat evenly, and local wind can change the cooling rate quickly. Portable preheat equipment, shielding from wind and a hold time calculated from the actual joint temperature are more useful than a nominal torch setting.

Melbourne and Brisbane workshops face a different market: short lead times, mixed job sizes and pressure to document work for clients and insurers. Australian shop talk treats the fit-up, root preparation and preheat as part of the weld, not paperwork around it. Where a contract invokes AS/NZS 1554 or another standard, check its scope and combine it with a qualified procedure and the project specification.

Put repeatable checks into the workshop

A welding procedure specification should define the grade, thickness range, joint, preparation, preheat, interpass limit, heat input, consumables, sequence, cleaning and inspection. Qualification should follow applicable Australian-adopted ISO standards and the client’s engineering requirements. Before striking the arc, operators should verify:

During welding, operators need feedback rather than a signed sheet alone. Changes in current, travel speed or wire feed alter the thermal cycle, and a qualified range should not be treated as a target to maximise production. The crew should:

Australian crews often move between workshops, sites and temporary plants, so competence records and equipment calibration matter. Training should explain the reasons behind each control, not only the steps in a work instruction. A change of joint, position, diameter or base material can move the job outside the qualified envelope and should trigger review before work continues. Photographs and dimensions provide useful evidence, but they do not replace calibrated temperature checks or traceable test reports.

Verify results and plan for long-term service

Inspection should address both the weld and the heat-affected zone. Visual examination is followed, where specified, by magnetic particle, dye penetrant or ultrasonic testing. Hardness surveys and mechanical test coupons can verify that the selected cycle did not create unacceptable brittleness. Because hydrogen-assisted cracking can be delayed, hold and re-inspection points may be required before a component is released. Residual stress can also influence fatigue and distortion during later machining, so stress relief or additional distortion checks may be needed before final acceptance.

If a crack is found, do not simply grind it out and weld again. Stop and isolate the component, establish the cause, obtain an engineering disposition and use a repair procedure appropriate to the remaining thickness and restraint. Keep records of heat input, preheat, inspection results and repair work so future failures can be investigated rather than guessed at.

Modern cells can improve consistency, although laser welding creates a narrow heat-affected zone and rapid solidification that still demand clean, stable fit-up. Where automation also includes sensor or power-lead assembly, choices for coaxial cable preparation affect cell uptime but do not replace steel-welding controls. Trial coupons, representative joints and defined acceptance criteria remain the basis for approving any process.